- Do you have any questions concerning this product?
- Hersteller-Kontaktdaten
- Further products by OldtimerWerk
- Order number: 101714
- OEM reference: 171 511 433;171 511 453;171 511 413;171 511 437
- Installation position / instructions: Montagesatz Hinterachse
- Restrictions: 20,5mm Stabilisator
- Vehicle usage: Caddy (14D), Golf 1 (1974-1983), Golf 1 Cabrio (1979-1993), Jetta 1(1979-1984), Scirocco 1 (1974-1981), Scirocco 2 (1981-1992)
If your Golf 1 feels unstable when cornering or the rear axle becomes unstable, the stabiliser bearings are usually worn out.
This mounting kit includes everything you need for the 20.5 mm stabiliser on the rear axle: rubber bearings for the inside and outside, clamps with tension brackets and all the mounting hardware, including screws, washers and self-locking nuts. The kit fits the Golf 1, Golf 1 Cabrio, Jetta 1, Scirocco 1 & 2 and Caddy 14D. OE numbers are 171511433, 171511453, 171511413 and 171511437.
Once reassembled, the car will once again handle corners with ease.
The repair kit for your stabiliser consists of the following individual parts:
Rubber for rear/centre stabiliser Golf 1 & Co OE Ref. 171511413
Rubber bearing, rear/outer, stabiliser 20.5 mm, Golf 1 & Co OE Ref. 171511437
Clamp suitable for stabiliser clamp, Golf 1 & Co, OE Ref. 171511453
Clamp for stabiliser, rear, Golf 1 & Co, OE Ref. 171511433
Hexagon screw M8X20
Washer M8
Hexagon nut M8 self-locking
Auf unsere Eigenfertigungen aus Meisterhand sind wir ein wenig Stolz. So stellen wir zum Beispiel fertig gebördelte Bremsleitungssätze zusammen, die euch auch das mühsame Zusammenstellen von Einzelkomponenten ersparen. Und Teile, die große Anbieter mangels Stückzahl nicht mehr produzieren wollen, nehmen wir selber in die Hand und fertigen Sie nach.
Anschrift:
OLDTIMERWERK
Zu den Mühlen 6
75399 Unterreichenbach
Deutschland
Telefon: +49 7231/6076574
E-Mail: [email protected]
If your Golf 1 feels unstable when cornering or the rear axle becomes unstable, the stabiliser bearings are usually worn out.
This mounting kit includes everything you need for the 20.5 mm stabiliser on the rear axle: rubber bearings for the inside and outside, clamps with tension brackets and all the mounting hardware, including screws, washers and self-locking nuts. The kit fits the Golf 1, Golf 1 Cabrio, Jetta 1, Scirocco 1 & 2 and Caddy 14D. OE numbers are 171511433, 171511453, 171511413 and 171511437.
Once reassembled, the car will once again handle corners with ease.
The repair kit for your stabiliser consists of the following individual parts:
Rubber for rear/centre stabiliser Golf 1 & Co OE Ref. 171511413
Rubber bearing, rear/outer, stabiliser 20.5 mm, Golf 1 & Co OE Ref. 171511437
Clamp suitable for stabiliser clamp, Golf 1 & Co, OE Ref. 171511453
Clamp for stabiliser, rear, Golf 1 & Co, OE Ref. 171511433
Hexagon screw M8X20
Washer M8
Hexagon nut M8 self-locking
- Do you have any questions concerning this product?
- Hersteller-Kontaktdaten
- Further products by OldtimerWerk
Auf unsere Eigenfertigungen aus Meisterhand sind wir ein wenig Stolz. So stellen wir zum Beispiel fertig gebördelte Bremsleitungssätze zusammen, die euch auch das mühsame Zusammenstellen von Einzelkomponenten ersparen. Und Teile, die große Anbieter mangels Stückzahl nicht mehr produzieren wollen, nehmen wir selber in die Hand und fertigen Sie nach.
Anschrift:
OLDTIMERWERK
Zu den Mühlen 6
75399 Unterreichenbach
Deutschland
Telefon: +49 7231/6076574
E-Mail: [email protected]